Running blind to time and distance

One lacks GPS, the other lacks a strap

Today's run (street): 3.75 miles
Yesterday's run (street): 4.5 miles

They ran the Dirty Sock this morning and I cannot imagine how those poor runners managed through 6.2 miles of hot and steamy air. Make that wet air. Air that you can feel without a breeze. The humidity today and yesterday could only be described as brutal. Despite that, I did get out Saturday and today, although there was nothing about my running that could be mistaken for a racing level effort.

Yesterday was the first time I ran without my FR210 on my wrist since I bought it, and it was disconcerting not to be able to monitor time or distance. I put the watch in my SPIbelt and tried to listen for the chirp that indicated mile splits, but I was unable hear them. Without that information, I had to guess my mileage based on the route I was running. I was surprised at the end to see that I'd covered 4.5 miles in sweltering conditions. I got home and jumped in the pool wearing my running clothes. Learning from past errors, I carefully removed my phone, Garmin and Fitbit before diving in.

This morning I'd planned to get out before the direct sun added to the already hot day. Unfortunately, I didn't actually start until 7:40 AM. By then, the air felt like a steam bath. After yesterday's experience  running without either distance or time indicators, I decided to put a new battery in my old FR60. At least I'd have a stopwatch to reference.

Equipped with phone, Fitbit and two Garmins, I set off into the heat and humidity. I still couldn't monitor my distance progress unless I pulled my GPS watch from my SPIbelt, not an easy thing to do while running. I felt like I ran more than 3.75 miles, but in this weather, that was more than enough.

Running with 1 1/2 watches is going to get old real fast. My FR210 wristband has further disassembled past the point where I could repair it with this cool hack. I should probably buy another GPS watch, but that seems wasteful because both the watch and GPS part of my FR210 still works. I'm open to suggestions.

In term of this weekend's running, my paces today and yesterday were glacial. Still, I enjoyed the fact that I'm getting through every run without worrying when fatigue will kick in. Even though conditions were suboptimal, I never once wished these runs would end. If I had run the Dirty Sock today in this weather I would have gotten through it. But not very quickly.

Short and sweat

All the kings horses and all the black tape...

Today's run (street): 2.6 miles

So very hot and humid this morning. I probably should have stayed indoors, cranked the AC, and set the treadmill and floor fans to max. Instead, I decided to brave the mid-August swelter. I can usually endure any type of weather for three miles (or in today's case, something less to that) and would have done 3+ today, but I had very little time to run and shower before my first meeting of the day.

Gimme swelter

Despite conditions, I was eager to get outside,. When I picked up my Garmin, the bottom half of the strap separated from the top, despite the awesome repair work I've been doing with electrical tape. My sister-in-law told me about some material that will fix rubbery plastic like this wristband, but I fear it's too late to save the FR210.

I ended up taping the watch all the way around and that secured it well enough to get through 2.63 miles. I really don't want to do that every time I want to take it on a run. The watch itself works fine so I guess, for now, I'll stick it in my SPIbelt. There is a hack to fix a Garmin that suffered wristband failure, but it requires that the first two loops that connect to the watch case be intact. One side is beginning to rip, so maybe not.

So what to do? I can continue carrying it with me or I could buy another watch. I've had this Garmin for about five years and it has served me well. I don't like replacing technology that still provides utility, but in this case it wasn't the technology that failed me.

Frustration mounts with the ProForm CE 6.0

Hey elliptical, you've gotta screw loose!

Today's workout (elliptical): 25 minutes

Today has been busy. This morning was filled with meetings and this afternoon I presented a technical paper at a W3C conference. I'd had a much different expectation about early retirement. Tomorrow will be even busier. 

This morning I decided to use the new elliptical while my wife ran on the treadmill. It was my second time using the machine and, once again, I was disappointed. I had hoped that this ProForm, that looks a lot like our old X1, would perform in similar way. Aside from the fact that they both provide elliptical motion, the user experience is far opposite.

The difference is in the quality. The X1 had its challenges, but it was a sturdy beast. The ProForm CE 6.0 is a wobbly contraption that squeaks and squeals. The display shows your distance only in revolutions (huh?) and there's no way to pause the timer during a workout.

Why would need to pause the timer? One reason might be that the bolt that attaches the arm to the center post tends to work its way free. I had to jump off the machine this morning at one point and tighten it with an Allen wrench. Lucky for me, I'd removed the decorative plastic collar last week to get to this bolt. I needed to break the collar's connecting tabs when I did that, so it's not going back on.

The rest of my workout went without incident and the bolt stayed in after my mid-session triage. While I consider the CE 6.0 far inferior to the unit it replaced, I still ended up with good workout that got my heart rate to target. It will be back to the treadmill tomorrow. I can't believe I'm saying this, but I'm actually looking forward to using it.

Our BH X1 is a bad houseguest

BH Fitness X1: down for the count?

Today's run (treadmill): 25 minutes

This weekend we had guests who stayed over in our spare bedroom. It's actually a misnomer to characterize this room as a spare because, next to the kitchen and den, it is easily the most utilized room in the house. Besides being the staging area for my morning runs, the guestroom is also where my wife does her daily treadmill workouts and it occasionally serves as my home office.

The guest room is fairly large and, besides having a bed, side table, armoire, wall unit and work table, it also contains a treadmill and an elliptical machine. The elliptical has been dormant, awaiting parts since March. Still, with all that stuff, the workout section of the room can seem a little tight. If we'd known back in March that our BH Fitness X1 was going to be out of commission for seven months (and counting), I'm sure we'd have either moved it to the basement or kicked it to the curb. But it sits there every day, mocking us for naively thinking BH Fitness will some day send us the needed parts.

I really miss using the elliptical and we had high hopes when our local service person (unaffiliated with BH Fitness) informed us that that replacement parts had come in. Unfortunately, once the technician arrived, we learned that they'd sent the wrong parts. I'll try to be diplomatic here and just say that BH Fitness machines are overpriced, seem to wear out quickly and you can't get parts. On the other hand, if you live on Long Island and need your home equipment fixed, I'd certainly recommend Busted Fitness.

We hope to learn soon if the correct elliptical parts will ever come. If the answer is no, we'll have to decide whether to buy a new unit. If we do, I'm not sure what brand to buy or what level of machine to get. With our experience with the X1, I'm thinking the most important question is, "If it breaks, how quickly can it be fixed?"

The elliptical is damaged and the treadmill is down

Crack(ed) pipe on the X1 elliptical

Today's workout (elliptical): 25 minutes
I had great expectations for years of problem-free workouts when we took delivery of our Sole F63 treadmill two years ago. Our Pro-Form L18 treadmill had served us well for 13 years despite the daily pounding it received. The Sole is good unit, with a powerful motor, generous tread area, and some nice features. We did have some problems with belt slip, early on, and we needed to replace the console, but those issues got resolved under warranty.

With the impressive long term performance of the Pro-Form machine, I expected the Sole to do just as well. However, a few weeks ago, my wife and I noticed that the sound from the motor had become especially loud. A visit from the repairman revealed a number of problems with the unit, and he ordered replacement parts. The parts are still covered under warrenty, but not the labor. You can't have everything.

As we wait for the repair person to return next week, our only indoor option is to use the elliptical machine. This machine, a BH Fitness X1, has been a solid performer, despite some initial problems at the beginning. It was expensive, relative to other units in its class, but its build quality is better than what you might find at Dick's Sporting Goods.

As it happened, the elliptical machine has also joined the disabled list, having cracked one of the struts that connects the pedal assembly to the dynamic arm assembly. I've been able to restore functionality by tightly wrapping the pipe-end with duct tape, but the torque from the crack has cantered the foot bed a couple of degrees to the left. It's not that bad and the unit is still usable. We worried that the slight shift would lead to leg or knee issues, but neither my wife nor I have experienced anything like that.

Our treadmill repair person is an independent contractor and I'm hoping that he might be able to replace the elliptical's pedal assembly after repairing the treadmill. I guess these units wear out, I'm just surprised how little time it takes before that happens.